How to Fix the “Scanning And Repairing Drive Stuck At 100” Error? (7 Solutions!)

Did you scan and repair your hard drive, but it’s taking longer than expected? This error occurs during the boot process of your computer. The cause of this issue is mainly due to an incorrect shutdown or when the computer experiences an unexpected power outage.

When you are stuck on this screen, the first thing you can do is to forcefully restart the computer by pressing and holding the power button before attempting any other fixes. In this article, we’ll discuss all the most effective solutions to fix this frustrating issue quickly.

Causes of Scanning and Repairing Drive Stuck at 100

When certain Windows users attempt to boot their computer, scanning and repairing drives may get stuck. This error may last for anywhere from a few minutes to hours. The “scanning and repairing drive stuck at 100” error can be caused by various factors, including:

• The computer did not shut down properly. This could be due to a forced shutdown or a power outage while in use.
• The computer’s hard drive might be corrupted.
• The computer may be infected with Malware or virus.
• The device’s drivers are incorrectly configured.

Solution 1: Check the Drive Status

If there are problems with the hard drive, Windows will detect them and allow you to sweep and repair them by checking the drive status.

Step 1: Search for “Control Panel” in the Windows Search box and Locate “Security and Maintenance.”

Step 2: Select “Maintenance.” You should see a “Drive status” section where you may see issues recorded as well as a link to resolve them.

Solution 2: Run the Windows Error Checking Tool

Step 1: Open the Windows File Explorer and navigate to “Devices and Drives.”

Step 2: Select Properties from the context menu of the hard drive. 

Step 3: Go to the Tools section and click the Check button in the Error-checking section.

Step 4: Afterward, Windows will detect errors and prompt you to repair the drive.

Step 5: If no errors are found, Select Scan drive to repair it.

Step 6: Restart your computer to see if the issue has been resolved.

Solution 3: Disable Automatic Repair

Step 1: Turn on the computer by pressing the power button, and then, when the Windows logo appears, press the power button again to turn it off. Do this twice.

Step 2: Then, turn on the computer and wait. Your PC should be in Windows Recovery Environment.

Step 3: From the “Choose an option” section, navigate to “Troubleshoot” and then “Advanced options.”

Step 4: Press the Windows key + R to open the Run dialog and input “cmd” to bring up the command prompt. In the Command Prompt, type “bcdedit,” keeping the values “identifier” and “recoveryenabled” in mind. In general, it is “current” and “Yes.”

Step 5: Toggle off Automatic Repair, type bcdedit/set current recoveryenabled no.

Step 6: Reboot the computer.

Solution 4: Disable Check Disk

Step 1: Start your computer in Safe Mode and enter “regedit” into the Run dialog box.

Step 2: In the Session Manager, select BootExecute.

Step 3: In the pop-up window, modify the Value data to autocheckautochk/k:C * and then tap OK.

Step 4: Restart your computer to see if the issue is now fixed.

Solution 5: Run SFC Scan

An SFC scan can detect and repair any damaged or corrupt files created during installation.

Step 1: Start your computer by booting from the Windows installation media. Click the Repair button.

Step 2: Select Troubleshoot from the recovery window.

Step 3: Go to the Advanced tab.

Step 4: Then, click on Command Prompt.

Step 5: To run a system file scan, enter the following command:

sfc /scannow

Step 6: After running the SFC command, input this command to restore the system image and restart your computer.

DISM /Online /Image Cleanup /RestoreHealth

Solution 6: Boot into Safe Mode and Run CHKDSK

Step 1: Follow the step in ‘Solution 3’ to boot your computer in the Windows Recovery Environment.  

Step 2: From the “Choose an option” screen, navigate to Troubleshoot and select Advanced options.

Step 3: Select Startup Settings, then click on Restart and press F5.

Step 4: Navigate to “This PC” in the File Explorer, right-click the drive that is scanning and repairing.

Step 5: Select “Properties,” Then click on “Tools” and select “Check.”

Solution 7: Reinstall Windows

Step 1: Navigate to Settings, locate “Update and Security” and click on Recovery.

Step 2: Choose “Yes” on the request to switch applications that pops up on the screen.

Step 3: Then, a Fresh Start option will be displayed.

Step 4: Select “Get Started,” then click on “Next.”

Step 5: This will remove all programs not related to Windows.

Step 6: Press the “Next” button to begin downloading the latest Windows version. Afterward, install Windows, and this hard drive issue should be fixed. 

Conclusion

Nobody wants to constantly stare at a screen for hours, waiting for their drive to complete scanning and repairing. This issue is fairly common and can be quickly resolved with the solutions discussed in this article. Firstly, restart your computer to see if this issue is resolved. If it isn’t, try any of these seven solutions to get rid of this issue and continue using your computer.

Frequently Asked Questions